Tag: heating repair

How to Tell If Your Home Needs a Furnace Repair Service

If you are not getting heat in all parts of your home, there could be a problem with the air flow or your ducts. If this is the case, it will require a professional to resolve. First, check your thermostat setting. It may be set incorrectly. Next, try adjusting it up or down a few degrees.

Furnace Repair

If your breaker keeps tripping, it’s likely that there is a problem with one or more appliances. Unless the circuit is temporarily overloaded, a professional should look at the problem before you attempt any DIY fixes. Contact Cincinnati Furnace Repair for professional help.

Figure out which room or rooms the breaker controls. Then, unplug all the devices and appliances in that area. This will help you narrow down the source of the problem. If you see that a specific appliance trips the breaker repeatedly, try plugging it into a different outlet in that room on a different circuit. If it doesn’t trip the breaker, the issue may be with that outlet or switch instead of the equipment itself.

A tripped circuit breaker is usually caused by having too many devices on the same circuit. It can also be caused by a bad cord or plug, or a short circuit in a receptacle, switch, or fixture. If the breaker resets itself but continues to trip, it’s time to call in an electrician.

In homes with fuse boxes (as opposed to breaker panels), the process is slightly different. A fuse is made up of metal strips encased in glass, and it melts when there’s too much power. This is meant to break the circuit if there’s an overload, and it acts as a safety measure against fires.

If a fuse is blown, you’ll need to replace it with a new one. These can be found at any hardware store, but be sure to buy a replacement with the same amperage rating as the old one.

If you’re comfortable opening up your electrical panel, you can usually reset a tripped breaker by moving the switch to the off position and then back to on. Be careful not to move it to the middle position, which could be dangerous and may lead to another breaker trip. Be sure to shut off the power at the main breaker before doing this. If you’re not comfortable working on your home’s electrical system, it’s a good idea to call an electrician for safe and effective repair work.

Pilot Light Will Not Stay Lit

Your furnace’s system depends on the pilot light to stay lit. If it does not, the whole system is affected. It can be a shallow problem or an underlying issue, but either way, it needs to be fixed. A professional should handle the repairs to ensure safety and efficiency.

Depending on your style of gas furnace, the ignition system is controlled by a few different parts. The thermostat calls for heat, the draft inducer fan kicks in to pull air through the furnace, the gas valve opens to move gas into the pilot burner, an electronic spark ignites the gas, and a flame sensor tells the gas valve that the pilot light is lit. If the thermocouple or flame sensor is malfunctioning, the system will shut down because it can’t sense that the pilot is lit.

The best way to diagnose an issue with your gas furnace is to consult the manual that came with it. This should contain specific instructions for relighting the pilot, and it’s a better guide than general guides found online. It’s also important to turn off the power and gas supply to the furnace before starting any work. This will help prevent accidental damage to the equipment and possible injuries to yourself or others.

It is not uncommon for a pilot light to flicker or go out. This is because the tip of the pilot light can become corroded with soot and stop gas flow to it. If this is the case, a toothbrush can be used to scrub the tip of the pilot light and clean it. Additionally, the thermocouple can sometimes get bent. This causes it to not be in contact with the flame, which causes the gas valve to close.

The thermocouple can be repositioned by hand, though this should only be done with extreme caution. It’s a good idea to ask an experienced professional to do this as it can be complicated and dangerous. If the thermocouple or flame sensor cannot be repositioned, it may need to be replaced entirely. This is a part that will need to be replaced by a professional, as it is an essential safety component.

Pilot Light Is Flickering Yellow

If your pilot light is flickering yellow, the first thing you should do is make sure the breaker or fuse that powers the furnace has not been tripped. Then, switch the thermostat to the fan-only or auto position. Ensure that the gas valve is set to the on position.

Next, check the pilot orifice for a clog and clean it with a piece of wire. After doing so, the pilot flame should return to a blue color. If not, the problem may be more serious and you will need to consult your Carrier furnace manual.

It is also possible that the igniter fails or there is not enough gas flowing to the pilot light. This could be caused by a dirty tube that requires cleaning with something abrasive. In addition, a broken thermocouple can also cause the pilot light to flicker. In this case, you will need to repair or replace the device.

Another reason for a yellow blinking light is an overloaded blower motor. This is most often a sign of a belt that needs to be replaced. Consult your furnace manual for specific instructions on replacing the belt and how to relight the pilot light.

If the pilot light blinks yellow, it means there is a serious problem with your furnace and that you should contact a professional furnace maintenance company right away. This issue could be dangerous and can cause carbon monoxide poisoning, so it is important to get the problem resolved right away.

Regular maintenance will prevent many of the problems that can lead to a yellow blinking light. A technician will perform a variety of checks and repairs that will keep your furnace running smoothly and efficiently. They will check for a number of problems, including clogged vents and improper airflow, as well as inspecting and servicing the dozens of parts and subsystems that comprise your heating system. They will also look for signs of a potential electrical problem, such as loose connections or faulty components that can trigger a yellow flashing light and affect your comfort.

Burner Flame Is Yellow or Orange

If your furnace is producing a yellow or orange flame, it is a sign that it needs to be cleaned or repaired. This is a serious issue because it can indicate that your furnace is not combusting gas and oxygen properly, which can result in carbon monoxide poisoning. Carbon monoxide is an odorless, colorless gas that can cause nausea, headaches, and even death. It is important to have this problem fixed as soon as possible.

The flames on your natural gas burner should always be blue, with small traces of other colors from time to time. Anything other than this should be a cause for concern and requires the attention of a professional heating technician as soon as possible. A yellow or orange flame means that your furnace is not combusting the fuel and air properly, which can lead to wasted energy and expensive heating bills.

One common reason that your furnace’s flame may be turning orange is because of dirt build-up. When a furnace is dirty, it cannot properly combust the fuel and air to create heat and won’t burn off any of the extra exhaust. Another sign of a dirty furnace is a burning smell that comes from the unit and doesn’t disperse after a few minutes.

Another common cause for a yellow or orange flame is that there is not enough oxygen in the gas to ignite and combust it. This could be due to a dirty or clogged burner or a faulty blower. In this case, you should shut off your furnace immediately and call a specialist to check it out.

If you have tried turning the furnace breaker back on and it is still not working, try checking the main gas line to see if it is turned off. If the switch is off, it will need to be replaced before your furnace can work again.

Having a gas furnace that is not functioning correctly can make it difficult to keep your home comfortable and cozy. Ignoring these issues will only waste money on heating your home and can lead to dangerous problems such as a carbon monoxide leak. If you have any questions about your furnace or if you notice that the flame is not blue, contact the experts at LCU to schedule a heating repair service.

How To Choose The Right HVAC System For Your Home

If you want to purchase an HVAC system, it’s important to know what to look for. This includes cost, key terms, products, and basic maintenance schedules.

You’ll also need to learn about energy efficiency. This will help you to cut down on costs and keep your home comfortable. Clicking here at https://alltemprefrigerationfl.com/ will also save you on repair bills in the future.



Buying or replacing an HVAC system is expensive, but there are many factors to consider before making a purchase. Choosing the right one for your home requires research, help from a professional, and prioritizing your needs. It also involves evaluating the brand, the size of your house, and what add-ons you want.

The cost of an HVAC system depends on its type, brand, and size. In general, a higher-end system will be more expensive than a lower-end unit, but a high-efficiency system can save you money in the long run. In addition, a system with a warranty can reduce your overall costs by avoiding costly repairs.

Aside from the upfront cost of a new system, you should factor in the maintenance and energy bills as well. Energy-efficient systems can significantly reduce your utility bills and cut the amount of greenhouse gases that you consume. If you are interested in reducing your bills, make sure to ask about the available rebates and discounts.

It is also important to choose a system that can be used with a modern, programmable thermostat. This will allow you to control your heating and cooling from anywhere. You can also save money by turning the system off when you’re not at home.

Another factor to consider is what kind of fuel your system uses. If only certain fuel options are available or practical for your home, this will eliminate some options and narrow your search. It is also a good idea to have your ductwork inspected by a professional before choosing an HVAC system. Poorly sealed ducts can reduce efficiency by as much as 30%. In addition, a contractor can insulate your ducts and clean them to prevent air leaks.


Choosing the right wiring configuration for your HVAC system can help you save energy and improve performance. It also minimizes the risk of errors and ensures that your thermostat can work smoothly. Consult a professional or refer to the manufacturer’s guidelines for guidance.

Besides ensuring compatibility, you must also consider the capacity of your HVAC system. The size of your home will determine its heating and cooling needs, so you’ll need a unit with sufficient capacity to accommodate the space. If you choose a smaller unit, it’ll have to work harder to change the temperature in your home, and may not last as long.

The fuel type used by your system is another important factor to consider when determining which HVAC system is right for you. If you only have access to one or two fuel choices, it will narrow down your options and help you focus your research. The same is true for voltage requirements, as some systems run on different power supplies.

You must also consider your existing system’s compatibility with a smart thermostat. Many older systems were not designed with a smart thermostat in mind, so you’ll need to figure out whether yours can be hooked up to one. A professional HVAC expert can solder, cap, or replace stranded wires to make your system compatible with a smart thermostat.

Alternatively, you can use the compatibility checker to find out whether your existing system is compatible with a smart thermostat. The tool is easy to use and will only take a few minutes to complete. It will also allow you to see the results instantly. The test will tell you if your system is compatible with a Nest smart thermostat and whether it will work well in your home.

Energy Efficiency

When choosing the right HVAC system for your home, energy efficiency is a key factor. The higher the efficiency, the lower your energy costs will be. In addition, a high-efficiency HVAC system will reduce dangerous greenhouse gas emissions. When shopping for an HVAC system, look for the ENERGY STAR label. ENERGY STAR-certified systems must adhere to rigid energy efficiency standards. This means that they are more environmentally friendly than non-certified systems and will save you money on your electricity bills.

What size HVAC system you need is also important. Air conditioners are rated in BTUs, which represents the amount of work required to heat or cool one pound of water by 1 degree Fahrenheit. This can be a confusing term for consumers, but an HVAC professional can help you choose the correct system size for your home.

It’s also worth noting that HVAC systems come in a variety of designs and specs. Some are designed to heat and cool your entire house, while others are designed to heat or cool specific rooms of your home. A central air system is typically the most expensive choice, while a heat pump or ductless mini-split is much more affordable.

It’s a good idea to buy a system that’s compatible with your smart home devices. This will make it easier to control your HVAC system from anywhere in the world. In addition, it will save you money by automatically scheduling and adjusting temperatures. Some HVAC systems also include humidity control features that can reduce indoor pollutants and allergens. A warranty is an important consideration when buying a new HVAC system. Ensure that your contractor provides a warranty with their services, as well as any add-on components you might purchase.


When selecting an HVAC system, it is important to find a model with a long warranty. This will ensure that you can receive repair and replacement services in the event of a malfunction or defect. A good warranty should cover parts and labor for at least a year. Moreover, some manufacturers also offer extended warranties that cover parts and labor for a longer period.

Energy efficiency is a major factor when choosing an HVAC system. Make sure to purchase a unit with an energy efficiency rating of at least 15 SEER (seasonal energy efficient ratio). A higher rating indicates greater efficiency.

The size of your home will have a significant impact on your HVAC system’s efficiency. A smaller unit will work harder to heat or cool a larger space. This can result in an uneven temperature throughout the house and higher energy bills.

If you have a large home, consult with a professional to determine the right size HVAC system for your needs. Several factors must be considered, including the size of your home and its insulation, the type of windows, and the amount of sun exposure. A professional will perform Manual calculations to help you determine the correct heating and cooling load for your home.

It is also important to buy a low-maintenance HVAC system. Ask your contractor for details about maintenance and repair costs, and choose a model that is easy to maintain. You should also negotiate a service package that includes regular inspections and discounts on repairs. In addition, many modern HVAC systems include IAQ add-ons such as efficient air filter systems and humidifiers. Finally, consider the noise level of the HVAC system. Depending on the design and location of installation, some models can be quite loud.


Unlike other household products, which can simply be unboxed and plugged in, an HVAC system must be designed, customized, and fabricated for your home. Therefore, it’s important to work with a contractor who is quality-oriented and uses the best installation methods. This will ensure that your system is properly sized and works efficiently for years to come.

It’s also important to purchase a new high-efficiency HVAC system, as this will save you money in the long run. While these systems often cost more upfront, they also slash your cooling costs, which can help offset the initial investment. Additionally, you can negotiate with your contractor to get a low-interest financing option.

A good HVAC company will perform a manual method load calculation for your home. This is a complex formula that considers things like your home’s square footage, insulation levels, tree coverage, and sun exposure. It is important to know how many BTUs your home requires, as this will determine what size air conditioning unit you need. Air conditioners are sized by refrigeration tons, and one ton equals 12,000 BTUs.

Incorrectly sized HVAC systems are the most common cause of problems with heating and cooling in homes. This is because an undersized system will not provide adequate comfort and will wear out faster, while a large unit will cycle too frequently and may damage the indoor air quality in your home.

To prevent these issues, it’s important to keep all your vents open. While it may seem counterintuitive, closing vents reduces airflow and can affect how your system runs. You should also avoid using expensive air filters as they can slow down airflow over the coils, which can lead to freeze-ups. In addition, it’s a good idea to use a smart thermostat that allows you to manage your HVAC system from anywhere.